7 blade Ecovacs blade disc – Premium EvoSign tuning cutting disc made of glass fiber polypropylen

Optimized cutting performance – 7 blades for precise, even cutting.

Maximum stability – glass fiber reinforced polypropylene for lasting performance.

Easy installation – plug & play, perfect fit.

Secure fastening – Optimized collar screws ensure a firm hold.

Low wear – More blades, less maintenance.

47,99€ 36,99€

In stock - Ready to be shipped

Estimated delivery between 19 February and 21 February.

Perfection for ECOVACS GOAT G1, G1-800, G1-2000, O500, O800 RTK, O1200 RTK & GX-600

Maximum efficiency for your GOAT series: This high-quality blade disc is manufactured using a precise injection molding process and impresses with its extreme dimensional accuracy and high stability. With the glass fiber-reinforced 7-blade EvoSign Tuning blade disc, you can achieve precise cutting results in a flash.

 

Your advantages at a glance

✅ Suitable for: ECOVACS GOAT G1, G1-800, G1-2000, O500, O800 RTK, O1200 RTK & GX-600

✅ Dimensions: 187 mm Ø | 220 mm cutting width

✅ Ultra stable: Only 178g

✅ Original cutting heights: 100% identical to the factory blade disc

✅ Perfect fit: Compatible with (Ø 7 mm bolt circle) blades & M4 screws

✅ 7-blade system: More cutting surface for faster, more even mowing

✅ 4-way usable blades: Economical 2-hole design

✅ Free blade movement: Freely rotating blades for clean cuts

✅ Smooth-coated surface: Hardly any grass or dirt adhesion

✅ 1:1 installation: Directly like the original – quick and easy

✅ Force flow-optimized design: FEM-analyzed for maximum load capacity

✅ Glass fiber-reinforced Polypropylen: Weatherproof, water & chemical resistant, temperature resistant (cold & heat), impact resistant & tensile strength.

Color: Anthracite

📦 Scope of delivery

A ready-to-use 7-blade EvoSign tuning blade disc for ECOVACS GOAT mowing robots (without blades and screws)


Important note: Installation and operation are at your own risk. All manufacturer specifications, in particular safety instructions and warranty conditions, remain valid without restriction.

GPSR Information

Name: Markus Blohberger - EvoSign

Address: Nüchternbrunnweg 2

Email: support@greengears3d.com

Website: www.greengears3d.com

European Manufacturer: Yes

Name: Markus Blohberger

Address: Nüchternbrunnweg 2

Email: support@greengears3d.com

Website: www.greengears3d.com

Warnings

Safety Information

1. Safety instructions for mowing plates made of ASA material

Material properties and restrictions:

The mowing plate is made of high-quality, UV-resistant ASA material that is durable and weatherproof. Suitable for normal mechanical loads; extreme loads and temperatures above 80 °C can affect stability. Not suitable for applications other than robotic mowers.

General safety instructions:

Regularly check the cutting disc for cracks, wear or deformation. Use only compatible blades and mounting materials that are suitable for this cutting disc. The cutting disc may only be operated with the intended blades from our range or blades with the same dimensions to avoid damaging the robotic lawnmower.

Installation and removal:

Turn off the robotic mower and disconnect it from the power supply completely before installing or removing the mower deck. Use a suitable screwdriver for installation and tighten the screws only hand-tight. The use of a cordless screwdriver is not permitted.

Maintenance and inspection:

Regularly check for damage and replace the mowing disc if there is visible material fatigue. Clean the mowing disc with fresh water if necessary, avoiding aggressive chemicals.

Operating conditions:

The mowing disc is optimized for use on flat lawns. Avoid unevenness and obstacles such as stones, manhole covers, roots, etc., as these can cause damage.

2. Safety instructions for blades

Material properties:

The blades are made of high-quality stainless steel with a titanium carbide coating for maximum sharpness and durability.

General safety instructions:

Warning: the blades are extremely sharp. To avoid injury, wear suitable protective gloves when installing. Keep the blades out of the reach of children.

Installation and removal:

Make sure that the mower is switched off and that no energy source is connected. Use only the blades intended for the mower disc to ensure stability and safety.

Disposal:

To avoid injury, wrap the blades in paper or cloth before disposal and dispose of them in an environmentally friendly manner.

3. Safety instructions for adapters made of ASA material

Material properties and restrictions:

The adapters are made of UV-resistant ASA material and are specially designed to lower the cutting height. Adapters must not be combined with each other, as this can cause imbalance and instability.

General safety instructions:

Check the adapter regularly for cracks, wear or deformation. Use adapters only with compatible mower decks and robotic mowers. Adapters should only be used on level lawns, otherwise the additional lowering can cause damage to the lawn if it is cut too short. Keep the adapters out of reach of children under 3 years of age to avoid choking.

Installation and removal:

Use a screwdriver and tighten screws only hand-tight. The use of a cordless screwdriver is not allowed.

Maintenance and disposal:

Clean the adapter as needed with fresh water and avoid aggressive cleaning agents. Dispose of damaged adapters in an environmentally friendly and safe manner.

4. Safety instructions for mounting screws

Material properties:

The screws are made of galvanized, hardened steel or stainless steel and are specially designed for safe use in robotic lawn mowers.

General safety instructions:

Screws are small parts and can pose a choking hazard or risk of injury to children if not handled properly. Use only the screws supplied by us or screws with the same specifications.

Mounting and dismounting:

Screws may only be mounted or dismounted by hand using a suitable screwdriver. Cordless screwdrivers or electric tools are not permitted. Tighten the screws firmly, but avoid over-tightening to prevent damage to the thread or mounting.

Maintenance and inspection:

Regularly check the screws for secure fit and visible damage. Replace damaged screws immediately to ensure the stability of the mowing disc.

Disposal:

Dispose of damaged screws in an environmentally friendly way and pack them securely to avoid injury.

Summary of safety measures

Regularly check the condition of all components (cutting disc, blades, adapters and screws). Follow the assembly and maintenance instructions to ensure safe use. Keep all parts out of the reach of children and use them only for their intended purposes.

Keep out of reach of children.

SAFE & STABLE

Trouble-free operation – even on wet lawns thanks to precise collar screws

PRECISE CUT

7 blades for an even, perfect lwan cut.

LESS MAINTENANCE

Distributed load: Less maintenance and less frequent blade replacement.

MAXIMUM STABILITY

glass fiber-reinforced polypropylen for durable, high-performance use.

EFFICIENCY & SAVINGS

Optimized performance reduces costs and saves time.

Increased cutting performance

The higher number of blades means that even very dense lawns can be cut precisely and easily. The likelihood of plucking and the associated yellow blades of grass is reduced and the cut is more even.

Construction

When developing the blade discs, the aim was to achieve a weight-optimized design with greater stability and also to reduce noise emissions and soiling. The smooth surface without edges means that less grass clippings can accumulate, which can lead to imbalance.

Knife service life

The knife service life is increased by the longer blade length available for cutting due to the larger number of knives. The knives are mounted with an optimized mounting distance so that they can usually be rotated and reused.

Lassen Sie sich von unseren Kunden überzeugen.